SMW-AUTOBLOK
  1 Manual chucks 6 Closed center cylinders - Opden center cylinders
Double piston cylinders
  2 Closed center power chucks 7 Pneumatic front-end chucks
Control Units
  3 Open center power chucks
Collect chucks		 8 Self-centering steady rests
  4 Quick jaw change power chucks 9 Static chucks pneumatic/hydraulic
Bar pulling chucks
  5 Pull-down chucks - Compensating chucks
Indexing chucks - Shaft chucks		    
 
1.Manual chucks
HG-N
Tongue & groove
Jaw system original SMW
Manual chucks Ø 160 - 630 mm
with through-hole - QUICK JAW CHANGE
3 jaws
HG-F
Tongue & groove
Jaw system Forkardt
Manual chucks Ø 160 - 630 mm
with through-hole - QUICK JAW CHANGE
3 jaws
 
   
2.Closed center power chucks
AN-D
INCH serration 		AN-M
METRIC serration
High precision power chucks ¨ª 125 - 400 mm
closed center
2 and 3 jaws (4 jaws only ¨ª 400 mm)
AL-D
INCH serration 		AL-M
METRIC serration
High precision power chucks ¨ª 125 - 400 mm
closed center - LONG STROKE
2 and 3 jaws (4 jaws only ¨ª 400 mm)
AN-C
Tongue & groove
High precision power chucks ¨ª 165 - 400 mm
closed center
2 and 3 jaws (4 jaws only ¨ª 400 mm)
AP-D (new)
INCH serration
AP-M (new)
METRIC serration
High precision power chucks ¨ª 170 - 400 mm
proofline = fully sealed/low maintecance
closed center
3 jaws
AP-C (new)
Tongue & groove
High precision power chucks ¨ª 170 - 400 mm
proofline = fully sealed/low maintecance
closed center
3 jaws
IN-D
INCH serration 		IN-C
Tongue & groove
High precision power chucks ¨ª 500 - 800 mm
closed center
3 and 4 jaws
IL-D
INCH serration		 IL-C
METRIC serration
High precision power chucks ¨ª 500 - 800 mm
closed center - LONG STROKE
3 and 4 jaws
IN-D
Module 2
serration		 IR-C
Tongue & groove
Radial setting of jaws
High precision power chucks ¨ª 1000 - 1600 mm
closed center
3 and 6 jaws (all diameters)
RAN (new)
Pull down effect
Tongue & groove
High precision pull-down chucks ¨ª 170 - 400 mm
pull-down effect of inclined master jaws
3 jaws
CL-C
Tongue & groove 		CL-D
INCH serration
High precision power chucks ¨ª 80 - 315 mm
closed center - LONG STROKE
2 jaws
 
   
3.Open center power chucks
  / Collect chucks

BH-D
INCH serration

High precision power chucks Ø 130 - 315 mm
large through-hole
2, 3 and 4 jaws
BH-M
METRIC serration
High precision power chucks Ø 130 - 315 mm
large through-hole
2, 3 and 4 jaws
BB-D
INCH serration 		BB-M
METRIC serration
High precision power chucks Ø 140 - 315 mm
EXTRA LARGE through-hole
2, 3 and 4 jaws
GH-D
INCH serration
GH-M
METRIC serration
High precision power chucks  Ø 400 - 800 mm
large through-hole
3 jaws
HFKN-D
INCH serration		 HFKN-M
METRIC serration
High precision power chucks Ø 110 - 500 mm
wedge-bar design
large through-hole
3 jaws
BHD-FC
INCH serration		 BHM-FC
METRIC serration
High precision power chucks Ø 165 - 630 mm
large through-hole
CENTRIFUGAL FORCE COMPENSATION
3 jaws
KSZ-MB
Collet chucks		 KSZ-DZ (new)
Draw collet chuck for bars		 KSZ-DZ (new)
Draw collet chuck for bars
Power operated collet chucks
for bar machining
quick collet change
 
   
4.Quick jaw change power chucks
KNCS-N
QUICK JAW CHANGE
Quick jaw change power chucks Ø 140 - 630 mm
large through-hole
high speed
high flexibility: jaws radially adjustable/reversible
3 jaws
KNCS-NB
QUICK JAW CHANGE
Quick jaw change power chucks Ø 210 - 800 mm
large through-hole
high flexibility: jaws radially adjustable/reversible
3 jaws
SUITABLE TO TAKE ANY TYPE OF EXISTING TOP JAWS
AN-RM
Pallettized
QUICK JAW CHANGE
Quick jaw change power chucks Ø 165 - 400 mm
closed center
2 and 3 jaws
PALLET SYSTEM
BH-RM
Pallettized
QUICK JAW CHANGE
Quick jaw change power chucks Ø 165 - 315 mm
open center
2 and 3 jaws
PALLET SYSTEM
 
   
5.Pull-down chucks - Compensating chucks
  / Indexing chucks - Shaft chucks
TSF-C
Self centering floating jaws		 TSR-C
Self centering rigid jaws
Pull-down chucks Ø 170 - 530 mm
active pull-down
tongue & groove base jaws
proofline = fully sealed/low maintenance
TSF-RM
Self centering floating jaws		 TSR-RM
Self centering rigid jaws
Quick jaw change pull-down chucks Ø 170 - 530 mm
active pull-down
quick jaw change with pallets
tongue & groove pallets
proofline = fully sealed/low maintenance
TSF-CP
Compensating floating jaws		 TSR-CP
Compensating rigid jaws
Compensating pull-down chucks Ø 170 - 530 mm
active pull-down
tongue & groove base jaws
3 jaws
proofline = fully sealed/low maintenance
FRC (new)
Compensating jaws		 FRC-AB (new)
Compensating jaws with self-locking system
Compensating jaw chucks Ø 165 - 365 mm
large compensating stroke
fix or spring loaded center
proofline = fully sealed/low maintenance
TPT-C (new)
2+2 independent jaw movement, tongue & groove
2+2 jaw chucks with self-centering independent movement Ø 210 - 400 mm
closed center
AXN
Automatic indexing chuck		  
Automatic indexing chucks Ø 205 - 680 mm
hydraulic clamping and indexing
2 jaws
divisions: 4 x 90° / 8 x 45° / 3 x 120°/ 6 x 60° oder Sonder
proofline = fully sealed/low maintenance
centrifugal force compensation
KRS-NZ
Shaft chuck with face driver		  
Shaft turning chucks Ø 210 - 400 mm
self-centering jaws
jaws retrectable by movement of chuck body
complete machining of shafts in one set-up
built-in power operated/spring loaded face driver
GSA (new)
Shaft chuck wir face driver		  
Shaft turning chucks Ø 200 - 320 mm
compensating jaws retractable by movement of master jaws
complete machining of shafts in one set-up
proofline = fully sealed/low maintenance
built-in power operated/spring loaded face driver
DFR-ABS (new)
Diaphragm chuck
- quick jaw change		 DFR-ABS-KOMBI (new)
Diaphragm chuck with swing clamps
jaw/swing clamps quick change

Ø 210 - 400mm
work piece clamping in the O.D. or in the pitch line
centrifugal force compensation
proofline = fully sealed/low maintenance

 Ø 210 - 315mm
radial and axial clamping
flat gripping force curve
proofline = fully sealed/low maintenance
 
   
6.Closed center cylinders - Opden center cylinders
  / Double piston cylinders
SIN-S
Closed center
rotating hydraulic cylinders
up to 70 bar
central through-hole for air coolant
stroke control via proximity switch or LPS
VNK
Open center
rotating hydraulic cylinders
up to 45 bar
through hole Ø 37,5 - 127 mm
extra short overall dimensions
stroke control via proximity switch or LPS
VSG
Open center
rotating hydraulic cylinders
up to 30 bar
EXTRA LARGE THROUGH-HOLE Ø 135 - 204 mm
SIN-HL
Closed center
rotating hydraulic cylinder
up to 70 bar
central through-hole for air, coolent or oil
high-low gripping force clamping
stroke control via proximity switch or LPS
SIN-L
Closed center
rotating hydraulic cylinder
up to 70 bar
central through-hole for air, coolent or oil
LONG STROKE
ZHVD-SZ
Double piston
rotating hydraulic cylinders
up to 50 bar
central through-hole for air, coolent or oil
stroke control via proximity switch or LPS
CSN
Closed center rotating
pneumatic cylinders
up to 7 bar
stroke control
optional safety valve
 
   
7.Pneumatic front-end chucks
  / Control Units
SP + SP-ES
INCH serration
Front-end power chucks Ø 125 - 350 mm
large through-hole - self contained pneumatic cylinder
3 jaws
BIG BORE
INCH serration
Front-end pneumatic power chucks with
extra large through-hole Ø 140 - 534 mm
3 jaws - standart jaw stroke
BIG BORE ES
INCH serration
Front-end pneumatic power chucks with
extra large through-hole Ø 140 - 560 mm
3 jaws - extended jaw stroke
 
   
8.Self-centering steady rests
SLU
Self-centering
steady rests
9 standard sizes clamping range Ø 4 - 460 mm
Special sizes in request
SLU-B
Self-centering
steady rests
Extra compact with side mounted cylinder
6 standard sizes clamping range Ø 12 - 460 mm
Special sizes in request
SLUA
Self-centering
steady rests
additional pivoting upper arm
for automatic vertical loading
7 standard sizes clamping range Ø 4 - 460 mm
Special sizes in request
SLUA-B
Self-centering
steady rests
extra compact with side mounted cylinder
and additional piovoting upper arm
for automatic vertical loading
5 standard sizes clamping range Ø 12 - 460 mm
Special sizes in request
KLU
Self-centering
steady rests
Standard series with narrow arms for crankshafts
 
   
9.Static chucks pneumatic/hydraulic
  Bar pulling chucks
US-CL
With 2 jaws long
stroke chucks		 US-A
With 3 jaws long or
normal stroke chucks
Static hydraulic gripping units
with built-on hydraulic cylinder
Ø 80 - 315 mm
static cylinder + chucks units
closed center chucks type CL/AN/AL
HB-D
INCH serration
2 and 3 jaws		 HB-C
Tongue & groove
3 jaws
Static hydraulic gripping units
Ø 130 - 315 mm
2 and 3 jaws
PB-D
INCH serration
2 and 3 jaws		 PB-C
Tongue & groove
3 jaws
Pneumatic chuck fixtures with built-in cylinder
Ø 130 - 315 mm
2 and 3 jaws
STP INCH serration
3 jaws		  
Pneumatic chuck fixtures with built-in cylinder
Ø 125 - 280 mm
with through-hole
M2-PB
Multiple fxture
with 2 chucks		 M4-PB
Multiple fxture
with 4 chucks
Pneumatic multiple fixture for machining centers
Ø 130 - 315 mm
2 and 3 jaws
PBI-D
INCH serration
2 and 3 jaws		 PBI-C
Tongue & groove
3 jaws
Rotating pneumatic chuck fixtures for indexing tables
Ø 165 - 315 mm
2 and 3 jaws
GF 80
INCH serration
bar pulling chuck
  
Spring operated bar pulling chuck
for stationary outside clamping